HP Designjet 600, 650 Plotter Reparatur
Ersatzteile, Verkauf, Fehler – Hamburg


Im Großraum Hamburg und Norddeutschland reparieren wir gerne bei Ihnen vor Ort und haben die Ersatzteile im Werkstattwagen. Eine Kostenorientierung finden Sie auf unserer Startseite.
Bitte nehmen Sie Kontakt mit uns auf.


Teileliste

 		ausblenden

Weitere Teile auf Anfrage

Für die Drucker/Plotter dieser HP Designjet Modellreihe haben wir ein umfangreiches Ersatzteilsortiment auf Lager, auch viele nicht aufgelistete Teile.


HP DesignJet Modell C1633A und C1633B A0 — 36" (Modelnummern: C1633A, C1633B)
HP DesignJet 600 A1, A0 — 24", 36" (Modelnummern: C2847A, C2848A)
HP DesignJet 650 C A1 — 24" (Modelnummern: C2858A, C2858B, C2859A, C2859B)
HP DesignJet 650 C PS A0 — 36" (Modelnummern: C3791A, C3792A)
1500-0855
SF-M284-2 		HP Motor-Zahnriemen (kleiner Zahnriemen, original HP)*2
— HP Motor Belt (small Belt, original HP)
 € auf Anfrage*1
Version A1 — 24"
X470002900.01 HP Zahnriemen für Druckschlitten (A1, original HP)*2
— HP Carriage Belt (24", original HP)
 € auf Anfrage*1
Version A0 — 36"
1500-0856
K1500085600.01 		HP Zahnriemen für Druckschlitten (A0, original HP)*2
— HP Carriage Belt (36", original HP)
 € auf Anfrage*1

*1 Alle Preise in Deutschland zzgl. USt.. Die angegebenen Preise sind aufgrund der starken Marktpreisschwankungen Richtpreise. Bitte erfragen Sie die aktuellen Preise.
*2 Einbau nur durch geschultes Fachpersonal; ggf. Kalibrierung des Gerätes erforderlich.


Weitere Hersteller und Modelle auf Anfrage.
Vorbehaltlich der Lieferfähigkeit des jeweiligen Herstellers.

ausblenden

Fehler (Error Codes)

 		ausblenden

Bei Fragen zum Fehler-Code nehmen Sie gerne Kontakt mit unserem Support auf.


Fehler-Code
— Error Code 		Beschreibung / Empfehlung
— Description / Recommendation
Designjet 600, 650 Fehler 010024 Pen interface ASIC test failure.
→ Solution: Replace main PCA.
Designjet 600, 650 Fehler 010025 Communication failure between the main and servo processors. Communication occurs through the processor support ASIC.
→ Correctiv Actions: Replace main PCA.
Designjet 600, 650 Fehler 010026 Servo interrupts not occurring or not reaching themainprocessorthrough the processor support ASIC.
→ Correctiv Actions: Replace main PCA.
Designjet 600, 650 Fehler 010027 Error in servo drive calculations.
→ Correctiv Actions: Replace main PCA.
Designjet 600, 650 Fehler 010028 Error in EEROM checksum calculations.
→ Correctiv Actions: Replace or clear EEROM. Replace main PCA. Performall calibrations. Press Enter to temporarily clear.
Designjet 600, 650 Fehler 010029 Error in EEROM write.
→ Correctiv Actions: Replace or clear EEROM. Replace main PCA. Perform all calibrations.
Designjet 600, 650 Fehler 01002a RS-232-C loopback test failure.
→ Correctiv Actions: Replace main PCA.
Designjet 600, 650 Fehler 01002b Centronics test failure.
→ Correctiv Actions: Replace main PCA.
Designjet 600, 650 Fehler 01002c Servo processor communication error.
→ Correctiv Actions: Replace main PCA.
Designjet 600, 650 Fehler 01002f DRAM test failure.
→ Correctiv Actions: Replace main PCA.
Designjet 600, 650 Fehler
010030
010031		 Failed communications betweenthecarriageand mainprocessors.
→ Correctiv Actions: For all 01003X codes, check trailing cable connections and continuity. If needed,replace the main PCA or the carriage assembly.
Designjet 600, 650 Fehler 010032 Carriage ASIC test failure.
→ Correctiv Actions: Refer to 010030.
Designjet 600, 650 Fehler 010033 Pen interface ASIC and carriage ASIC link test failure.
→ Correctiv Actions: Refer to 010030.
Designjet 600, 650 Fehler 010040 Error detected in X-axis servo feedback loop.
→ Correctiv Actions: Check X-encoder, encoder cable, main PCA.
Designjet 600, 650 Fehler 010041 Error detected in Y-axis servo feedback loop.
→ Correctiv Actions: Check encoder strip, carriage assem- bly, trailing cable, main PCA.
Designjet 600, 650 Fehler 010050 Uppermost SIMM indicates a failure.
→ Correctiv Actions: Replace uppermost SIMM.
Designjet 600, 650 Fehler 010051 Next to uppermost SIMM indicates a failure.
→ Correctiv Actions: Replace next to uppermost SIMM.
Designjet 600, 650 Fehler 010052 Both upper and lower SIMMs indicate a failure.
→ Correctiv Actions: Replace both upper and lower SIMMs.
Designjet 600, 650 Fehler 010080 RS-232-C data overflow.
→ Correctiv Actions: Data byte was not read before another was entered into the UART. Replace main PCA. If problem remains report the firmware problem to the HP Response Center or the nearest HP Sales and Support Office.
Designjet 600, 650 Fehler
020001
020002		 Firmware problem. Bad EPROMS.
→ Correctiv Actions: For all 2XXXX errors, report the firmware problem to the HP Response Center or the nearest HP Sales and Support Office. Note conditions before the error occurred. Include system configuration in the report.
Designjet 600, 650 Fehler 030000 X-axis shutdown.
→ Correctiv Actions: All 300XX errors indicate a failure of hardware or electronics of the X- or Y-Axis. Refer to SERVO CONTROL SYSTEM FAILURES in this chapter.
Designjet 600, 650 Fehler 030001 Y-axis shutdown.
→ Correctiv Actions: Refer to code 030000.
Designjet 600, 650 Fehler 030002 Y-axis friction too high.
→ Correctiv Actions: Refer to code 030000.
Designjet 600, 650 Fehler 030003 Y-axis failure.
→ Correctiv Actions: Refer to code 030000.
Designjet 600, 650 Fehler 030010 Excess friction in pen capping assembly.
→ Correctiv Actions: Check mechanical parts in pen cap- ping assembly for binding.
Designjet 600, 650 Fehler 04xxxx MIO interface error.
→ Correctiv Actions: If an MIO is installed, check the MIO setup. Then replace the MIO.
Designjet 600, 650 Fehler 05xxxx Problem Description Plotter system errors found.
→ Correctiv Actions: MIO problem is indicated. The most likely cause is the main PCA or the interconnect PCA. Replace the interconnect PCA. Replace the main PCA.
Designjet 600, 650 Fehler 060111 Line sensor LED not bright enough.
→ Correctiv Actions: The optical sensor on the carriage has failed to locate lines drawn during the pen calibration routine. Reduce the ambient light. If the media is not clean and reflective, change the media. If the lines are faint, replace the pens. Clean lenses. Replace LED. Use the Edge detect test, found in the service menu, to help troubleshoot.
Designjet 600, 650 Fehler 060302 Large final residual correction.
→ Correctiv Actions: Refer to code 060111.
Designjet 600, 650 Fehler 0700xx Could not calibrate for the drop detect sensor location.
→ Correctiv Actions: Check that the sensor and the sensor housing are properly aligned. Check that the service station cover is correctly seated over the sensor housing. Check that the sensor housing opening is clear of obstructions. Use the Pen nozzle and Drop detect tests, found in the service menu, to help troubleshoot. Use the Drop detect calibration, found in the service menu to recalibrate the position of the sensor. Check the drop sense cable connections. Replace the drop sensor.
Designjet 600, 650 Fehler 0f0000 Firmware error.
→ Correctiv Actions: Notify the HP Response Center or the nearest HP Sales and Support Office.
ausblenden